【產品簡介】
名 稱：塑料道釘
材 料：塑料加玻纖、釘體ABS、反光片PC等多種材質
反 光 面：?jiǎn)蚊妗㈦p面
底部尺寸：100mm×100mm×20mm
【產品特點】
1. 由改性增強工程塑料加玻纖制成，兩次注塑成型，抗壓16噸以上，能耐受汽車輪胎的壓力和強大沖擊力，抗沖擊力極強;
2. 殼體兩側有把手位，方便工人安裝時捏拿殼體而不弄臟反射器;
3. 道釘?shù)酌嫣厥饧y路設計，用膠水粘接，與地面牢固連接，穩定性強經久耐用;
4. 耐高低溫、耐水、耐油、耐化學、耐鹽堿腐蝕、耐風沙磨損;
5. 反射器性能好，反射器為微棱鏡全反射反射器，反光亮度達到鉆石級反光亮度。
【產品用途】
固定在路面上，用來標記中心線、車道分界線、邊緣線、彎道、進出匝道、導流標線、道路變窄、路面障礙等路段，起標線作用。停車場道路或地下車庫道路可單獨設置，也可配合標線使用。
【安裝方法】
1. 擺放安裝安全隔離設施，這一點是重重之重，希望大家一定不能忽略，而且在整個動態施工的過程中，不論是新建道路，還是已通車道路，所有人都應該在安全設施內，如在通車道路里施工，安全人員同安裝人員比例應為1：1。未通車路段施工，安全人員同安裝人員比例應為1：3。
2.確定安裝位置，確保安裝位置平整，對有伸縮、夾縫和不平整的路面，事先要將路面整理平整。
3. 用刷子把安裝位置清掃干凈，同時確保安裝位置干燥。
4. 取適量膠水均勻涂抹在道釘上。
5. 將道釘緊緊按在安裝位置上，確保方向正確，如果膠水多了，一定要清理干凈；
6. 如果是鑄鋁帶腳道釘，要確�？孜簧疃却笥卺斈_深度1cm，孔位直徑大于釘腳直徑2mm。
7. 道釘安裝完畢后兩個小時內要做一次巡視，確保所有的道釘沒有裝反、裝歪或壓歪。
8. 等道釘固化4個小時后，撤掉安裝隔離設施。
道釘安裝并不是一件復雜的事情，但卻有很多細節需要注意。這些細節對于保證道釘?shù)钠焚|(zhì)要求以及使用壽命起著非常重要的作用。
出口說明：
[ introduction ]
Name: Plastic spike
Material material: plastic and fiberglass, the nail body ABS, reflective film PC and other materials
An optical surface: single-sided, double-sided
Bottom size:100mm * 100mm * 20MM
Spike is also called processes signs or traffic signs, modified by a reinforced engineering plastic and fiberglass material, two injection molding, through the Ministry of certification, in line with national standards JT / T390 - 1999, can be a variety of road use. High and low temperature resistance, water resistance, oil resistance, resistance to chemical substances such as erosion, strong resistance, can resist all kinds of automobile tires, shocks.
Prism reflector can reflect the diamond in the night light, so that the driver in the150--200m can be obviously seen diamond reflective. Bright color appearance, reasonable shape and diamond Jingying reflective, very be good to hear or see, lighting the road as well as to beautify the city.
[ Characteristics ]
1 by modified reinforced engineering plastic and fiberglass material, two injection molding, compression of more than 16 tons, the tolerance of vehicle tire pressure and strong impact force, impact resistance and strong;
The 2sides of the shell with a handle, convenient installation pinch shell without soiling reflector;
The bottom3spike special texture design, by the adhesive, and the ground firmly connected, stability and durable;
4high and low temperature resistance, water resistance, oil resistance, chemical resistance, salt resistance, corrosion resistance of sand abrasion;
The 5 reflector reflector for good performance, the micro prism total reflection reflector, reflective brightness achieve diamond-level reflective brightness.
[ usage ]
Fixed on the road surface, used to mark the center line, the lane lines, edges, corners, and ramp, guide marking, road narrows, road barriers and other sections, marking role play. Underground garage parking road or path can be set independently, can also be used with marking.
[ ] the installation method
1placement and installation safety isolation facilities, it is a heavy weight, hope everybody must not be ignored, but in the entire dynamic construction process, regardless of is the new road, still has opened the road, everyone should be in the safety facilities, such as the opening of road construction, security personnel and installation personnel should be the ratio1:1. Open to traffic road construction, security personnel and installation of officers should be in proportion of 1:3.
2determine the location of installation, ensure the installation position on the flat, flexible, crack and uneven pavement, prior to the pavement smooth.
3brush clean installation position, while ensuring that the installation position of drying.
4apply the glue evenly in the spike on the.
5will spike firmly on the installation position, ensure the correct direction, if the glue more, must be clean;
6if it is aluminum with foot spike, to ensure that the hole depth is larger than1cm nail foot depth, hole diameter is larger than the pin diameter 2mm.
The 7spike installed after two hours to do an inspection, to ensure that all spike not anti-loaded, loaded askew or pressure distortion.
8spike cured after 4 hours, remove mounting isolation facilities.
Spike is mounted is a complex thing, but there are many details need attention. These details to ensure the quality and service life of spike plays a very important role. |
免責聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責，www.qy6.com對此不承擔任何責任。如有侵犯您的權益，請來信通知?jiǎng)h除。